Quartz Countertops in Albuquerque & Central New Mexico
Engineered stone that never needs sealing — fabricated and installed by the crew that measured it.
- 4.0 ★ Google
- Owner on every job
- Own fabrication shop
- Free on-site estimates
JYJ FLIPS LLC provides quartz countertops across Albuquerque, Rio Rancho, Santa Fe, the East Mountains, and Valencia County, fabricated in our own shop at 2369 Old Hwy 66, Edgewood, and installed by the owner. Fabrication and installation of engineered quartz countertops for kitchens and bathrooms in central New Mexico. $65–$120 per sq ft installed.
- Service area
- 18 communities, no travel charge
- Shop
- 2369 Old Hwy 66, Edgewood, NM
- Phone
- (505) 203-5508
- Estimates
- Free, on-site, written quote from the owner
What engineered quartz actually is
Quartz countertops are not cut from a quartz quarry. They are manufactured — roughly ninety to ninety-three percent crushed natural quartz mixed with pigment and a resin binder, then pressed and cured into slabs. That process is what gives quartz its two defining advantages: it is non-porous, and it is consistent. The slab you approve is the slab you get, without the surprise mineral streak that makes natural stone exciting and occasionally frustrating.
Non-porous matters more than people expect. There is nothing for red wine, olive oil, or coffee to soak into, so it does not stain, and it never needs sealing. For a busy family kitchen where nobody is going to think about maintenance, that is usually the deciding factor.
The honest limitation — and it is a local one
The resin that makes quartz non-porous is also the part that does not love ultraviolet light. At our elevation the sun is genuinely harsher than it is at sea level, and a slab sitting in direct, unfiltered afternoon sun for years can shift in color. In a typical kitchen with normal window exposure this simply does not come up. In a sunroom, an outdoor kitchen, or a west-facing bar top with full glass, it can. When that is your situation we will tell you to use granite or quartzite instead. That is a smaller sale for us and the right call for you.
How we fabricate it
- Laser template once cabinets are set, so the fit is measured rather than estimated.
- CNC cutting for sink and cooktop cutouts, faucet holes, and clean inside corners.
- Seam planning. Quartz seams can be made genuinely tight. We show you where a seam has to go before we cut, and we place it where it is least visible.
- Edge profiles from a simple eased edge to a mitered waterfall that carries the pattern down the side of an island.
- Full-height backsplashes in the same material, which is a look quartz does especially well because the pattern actually matches.
- Tear-out, install, and cleanup by our own crew.
Living with quartz
Soap and water handles ninety percent of it. Avoid abrasive powders and harsh alkaline cleaners, which dull the surface over time. Use a trivet — the quartz itself does not care about heat, but the resin does, and a 500-degree pan set straight down can leave a mark that will not buff out. That is the entire maintenance list.
Choosing a countertop material in central New Mexico
Most people arrive with a material already in mind. We will fabricate whatever you choose, but we are also going to tell you where each one struggles, because the climate here is not neutral. Big south- and west-facing windows are common here, and high-altitude UV is harder on resin binders than it is on natural stone. Water across the metro runs hard, which spots dark polished surfaces and argues for keeping natural stone properly sealed.
- Granite — $55–$95 per sq ft installed. Igneous stone, every slab unique, indifferent to heat and sun. Needs sealing every one to three years. The default recommendation for sunrooms, outdoor bars, and anyone who cooks hard.
- Quartz — $65–$120 per sq ft installed. Engineered, non-porous, never sealed, consistent from sample to slab. The default for busy family kitchens and for anyone who will not think about maintenance. Keep it out of direct all-day sun.
- Marble — $75–$150 per sq ft installed. The most beautiful stone we cut and the softest. Perfect for vanities, fireplace surrounds, and a baking station. Etches from acids in a working kitchen, and we will say so.
- Quartzite — $85–$160 per sq ft installed. Natural stone that reads like marble and wears like granite. The answer when someone wants a white veined top in a kitchen that actually gets used.
Every one of those is templated, cut, and polished in our shop at 2369 Old Hwy 66, Edgewood, NM 87015, which is why we can hold a seam tight and keep an overhang even. You can see the full breakdown on our pricing guide.
Why hiring one shop for cabinets and countertops matters in New Mexico
Most remodels in New Mexico involve two companies who have never met: one sets cabinets, another fabricates stone. When the countertop does not sit flat, each explains why it is the other’s fault, and you are left holding a gap, a tube of caulk, and two phone numbers.
We run both sides under one roof. Cabinets are set and leveled by our crew, then the countertop is templated against those cabinets, cut in the same building, and installed by the same people. If something is off, it is ours, and there is nobody to point at. That is not a slogan. It is the reason the business is structured this way, and it is the reason the seams line up.
It also has a practical scheduling benefit. One contractor means one calendar, so cabinets and tops land in sequence instead of leaving your kitchen torn out for a week while a second company finds an opening.
How a project runs with us
- Call or send the form. Jesus answers, asks what you are trying to do, and books a time to come measure.
- On-site measurement and a straight conversation. We look at the room, the plumbing, the walls, and how you cook. If a material is wrong for your situation, this is where we say so.
- One written number. Template, fabrication, tear-out, install, haul-away, sealing. No per-item surprises after the fact.
- Slab or sample approval. For natural stone you see the actual slab and where the cuts land. For cabinets you approve a door sample and a finish chip.
- Fabrication in Edgewood. Cabinets built and finished in the shop. Countertops laser-templated once the cabinets are set and level, then cut on the CNC and polished.
- Install by the same crew. The people who measured are the people who build and the people who install. One point of contact from first visit to final walkthrough.
Countertop-only projects typically run one to two weeks from template to install. Full cabinet packages run four to eight weeks depending on wood and finish. A complete kitchen remodel is usually six to ten weeks once materials are approved.
Typical installed pricing
| Service | Typical range | Unit |
|---|---|---|
| Granite countertops | $55 – $95 | sq ft installed |
| Quartz countertops | $65 – $120 | sq ft installed |
| Marble countertops | $75 – $150 | sq ft installed |
| Quartzite countertops | $85 – $160 | sq ft installed |
Ranges include template, fabrication, standard edge, tear-out of existing tops, install, and sealing where applicable. Exotic slabs, waterfall edges, full-height backsplashes, and structural changes move a project toward the top of the range. Every job is quoted individually after an on-site measurement. See the full pricing guide →
Quartz Countertops by city
Where we install quartz countertops
- Albuquerque
- Northeast Heights
- North Valley
- Westside Albuquerque
- Los Ranchos de Albuquerque
- Rio Rancho
- Corrales
- Bernalillo
- Placitas
- Santa Fe
- Eldorado at Santa Fe
- Edgewood
- East Mountains
- Cedar Crest
- Tijeras
- Sandia Park
- Moriarty
- Los Lunas
Related services
Quartz Countertops Questions
Is quartz better than granite?
Neither is better outright — they fail in different directions. Quartz is engineered, roughly ninety percent ground natural quartz bound with resin, which makes it non-porous. It never needs sealing, it will not stain from wine or oil, and the pattern is consistent from slab to slab, so what you see in the showroom is what lands in your kitchen. Granite is natural, handles heat better, and every slab is unique. If you want predictability and zero maintenance, choose quartz. If you want a one-of-a-kind stone and do not mind sealing it, choose granite.
Will quartz fade in New Mexico sun?
This is the one real caution with quartz here, and most shops will not bring it up. The resin binder in engineered quartz is not as UV-stable as natural stone, and we get intense high-altitude sun. In a normal kitchen this is a non-issue. But for a sunroom, a patio bar, or a countertop that sits in direct unfiltered south or west sun for hours a day, we will steer you toward granite or quartzite instead. We would rather talk you out of the wrong material than warranty-argue about it in three years.
Do quartz countertops need to be sealed?
No. Quartz is non-porous, so there is nothing for a sealer to soak into. Clean it with soap and water or a mild cleaner. Skip anything highly abrasive or strongly alkaline, and use a trivet under very hot pans — the resin can scorch at temperatures that natural stone would ignore.
Can you match a specific brand or color?
Generally yes. Quartz is manufactured, so if you bring us a name and a color we can usually source it or show you a close equivalent. Bring a photo or a sample chip and we will tell you honestly whether the match is exact or approximate.